Search results

Sailcloth material is the most durable soft tops for jeeps. Regardless of where you buy them, if you want the OEM fit and durability, Bestop is the manufacturer of the Jeep soft tops.

Yes Sir granted that they can find it in their application catalog.. If not a dealer should be able to order you one.

If you decide to remove it to replace the gasket/ seal, remove the 2 small bolts on the sensor first to expose the tone ring inside.. You can do one of the following.; turn the crank shaft until you get the timing at top dead center with the #1 cylinder at the compression stroke. The tone ring...

OBD- On Board Diagnostics. That letter simply states that if there is any malfunctions or failures on the OBD system, Chrysler will repair the cause under an extended warranty code. Each module( computer ) that directly relates to the function of emissions or drivability issues that's caused by...

Nope, no luck. No frames there. Thanks anyway.

Speaking of rear windows for CJ7's, where can I find a rear window frame for the hardtop? .. I still have the glass but the frame is gone.

I used to use the Edelbrock electric fuel pump on mine but it doesn't seems to last for the price. Now I've been using a universal electric fuel pump from Napa auto parts with a constant 7psi without a regulator. I'm running that on an AMC 360 with the performer intake and 4bbl carb..

I hear y' a .. The best thing that people like you and I can do right now is to stay on top of what's being infringed and keeping in contact with your local state representatives and congressman voicing out what you want and what you don't want them to do.. It won't do much as an individual but...

Is this thread still alive? Just finished 2 builds this year..

3.6liter takes a total of 6qts. And no more.. If its overfilled, it will smoke out the tail pipe when you rev it up or driving down the road.

You would have to crawl into the back and remove the panel to access the latch mechanism and manually unlock and unlatch it. Sometimes, even when you hear the lock actuator make a sound, doesn't mean it's actually cycling..

I'm not sure if the Kentrol bumper is strong enough for the task. I mounted my winch on a wide " C " channel plate then bolted it to the top of the frame cross member support.

Very nice!! Great job!!

I'm using the Edelbrock Performer intake and carburetor on mine with the offroad spring kit.. It works well on steep angles. I would recommend you get the needle kit as well and see which best suit your taste in performance. The only negative feedback on this carburetor would be " it sucks gas...

Also, there should be a hole on the bottom of the distributor housing and a hole on the tone plate inside close by where the sensor wiring comes out to the side. You can use this alignment hole by placing an Allen wrench or pin in the hole to keep it in place as you line up the shaft down to the...

Try applying some lube on both latches and cable if possible. Check the cable ends and make sure there's no kinks or pinch on them. Test the latch that's inop by manually locking it with a screw driver and releasing it with the lever. If that's not latching, make sure the cable is not stuck in a...

That happens when there's a slight imperfection on the thread. Look at the pinion thread closely and make sure there's no burrs in them as well. You should be able to start threading the nut by hand until it gets to the locktite part then you will need to use a socket and ratchet. Once you start...

It's going to be really tight and you will need a set of different wheels with quite a bit of offset.

Wow 3.8?, that's unusual. When they said it was "re-setting" , do they mean the PCM is not storing the DTC'S or is it the OBD misfire monitor on 200 rev.cts that's resetting? . If it's the PCM resetting, I would say this is an electrical issue.. I've haven't encountered much issues with the 3.8...

There's a bleeder screw located on the upper radiator hose towards the engine. Make sure you open this bleeder (Allen screw) when your filling up your cooling system. Check and double check that all the air has burped out. You don't have to completely pull the screw out, just enough when you see...