Search results

Exercised two electrical connections on tranny-front and rear (input and output sensors???). Cleaned up ground strap on valve cover to firewall. Just did 11 miles and no speedo cutting out. Still no 4wd indicator. I heard if you jump the connectors on the 4wd the light should come on, is that...

Hmm Well I checked my transfer case switch and it is closer to a 25mm then the 22 mentioned in video. Soaking in PB now since it's hard to get a good grab right now. Regarding speedo, it worked as I went down the end of my road but I haven't taken it out yet. Usually it will crap out if I'm on...

I did not do any work on the transfer case, oil change and a foglight bulb replace and I actually fixed my from windshield washer pump. Jeep has been sitting and I'm trying to get it ready for sale. Cleaning it up and getting rid of all the bugs. You said speedo is on the back of the gear...

First issue is I lost my speedo. It was cutting out for a little while and now it rarely moves. Is that the speed sensor for tranny? Second issue is I lost my 4wd indicator lights on my dash. My part time light was staying on and recently I went into 4wd and it went off, now I have no 4wd...

Thanks so much JPNinPA. I will give it a go when I get a chance. This weekend, I stopped clearing codes with the MIL light on. I was getting all these mixed 02 heater related codes. Funny , today I get in the WJ to go home and MIL light was off. So I checked when I got home and there were...

So Jeep has been getting some use but not much (don't want to get a no inspection ticket).. It still is throwing 02 heaters codes, sometimes all 4 but usually P0138, bank 1 sensor 2. It will throw it too, after a fresh start if I clear the codes, usually by itself with no other codes. Jeep is...

I have a trickle charger for my 1974 BMW. I can swap it over to the Jeep for a few days. My regular battery charger has a setting for 2 amps also. Will give it a go. dlm ny country

Thanks. With the vehicle sitting for a while (at least 4 months), the battery has taken a turn for the worst. It doesn't hold good voltage over a few days of idle parking.

So after much sitting in my driveway after a failed Crank sensor, a leaking gas tank and rusted out skid plate for the gas tank, I got the ugly monster running ok. But I'm do for a NY inspection and I am getting codes related to the 02 sensors heaters. It's on all four 02 sensors and it is on...

I had a clunk in back too. It ended being the upper control arm and balljoint on top of the diff. Jeep Triangulation suspension?? Kinda crappy Replaced both....quiet and better handling. dlm ny country

Yeah that is what I'm thinking, plus over flow from the gas filler surround molding. Anyways, I got the tank hooked up. I ran an extension hose so I could reach the small filler hose. I used coolant line and a brass fitting to couple it to the original hose. There is a small gas vent hose near...

I took the skid plate and tank out of another Jeep WJ. Not sure of the year. Most likely, there are small mods done over the generation span (1999-2004 I think) and that is most likely what I am dealing with. Tank size and shape is pratically the same. I am curious to what that 2nd smaller...

So I got a replacement tank and a skid plate for my WJ. The gas tank has a different angle on the connection next to the gas filler nipple. Is that for overflow on gas when filling? I hope my hose will have enough length to reach the new tank attachment since it is a few inches away. My...

Well that looks nice but I am in a HUGE junk Yard. Several acres. No 110V/AC dlmrun ny country

So I went to pick n pull today. Struck out on the the two front bolts on the skid plate for gas tank that bolt to the frame. Got everything else off. Might go back next weekend and give it another shot. I used a 6 point 18mm 1/2 inch breaker bar WITH a pipe on the end . The 2 front most bolt...

Well you would NOT believe what happened tonight. Took out the Jeep to go to the store and I'm about 1 1/2 miles from my house and I hear this dragging noise. I'm thinking, OK I screwed something up. I pulled over asap on a side road and I see my gas tank dragging and leaking fuel. Lucky no fire...

Had a chance to get the crank sensor in. It was a pain in the butt but I managed to get it from underneath with two wobble tips and long extensions. Let the car idle for 1/2 hour and no shutdown. Will give it a few short runs around town before I feel it's road worthy once again. No issues with...

ODPA? I don't think I jumped a tooth. I think one of the sensors started acting up last week and then yesterday it started to show it ugly face. It did run for about 20 miles last night to get me home. So this morning I figured I'd give it a go and $120 bucks later after a tow I'm thinking the...

So just after leaving work my jeep died 3 times. Felt like fuel interruption. Car started back right away after dying each time. Made it home fine after 3rd stall and was surprised to see code 1391( cam or crank sensor). I noticed about a week ago car would buck just once right around the same...

So I took another look at my new fan clutch and it does spin if I rotate it but not freely like you said JP. Good think I checked too because I noticed the condenser fan wires had moved and were in the way of the engine cooling fan. They would have been cut by the blade. I zip tied them down out...