Search results

1063090 i used a stock one out of a cherokee... mounts to the factory mounts on my yj.... works well.. i can use a 1/2 inch impact, fill tires, reset beads... all sorts of stuff.. just be sure to keep it oiled with air tool oil... i also have a 3 gallon tank and a t-handle on the throttle to...

1063091 1/2 inch course...[addsig]

1063093 get rid of the track bar... you don't need it.. you will get a little lateral movement but not enough to worry about... when you put your lift in you probably used neoprene bushings... they are strong enough to keep the axle from moveing... also remove your sway bar... you will find...

1063094 ya...eaiser to swap the tub then entire drive train...[addsig]

1063372 Although a hemi in a jeep would be awesome and the coolness factor would be huge i have never seen one done.. thats not to say it has never been done... (i live a very sheltered life)... there is something to say about a awkward swap... i don't know any parts store that has an abundence...

1063699 thats not a shift light.... it's a "this side up" light :-D [addsig]

1064138 i used a air cond. compressor off a cherrokee to build an on board air set up.. a tank off a big rig. and manifolds and fittings from a local automotive supplier.. cost about 300 bucks by the time it was done.. used a 3/8 coupler from home depot to extend my stick and transfer case...

1064139 falkn lucky man... you could have been seriously hurt.. i'm glad to here it was just the tail gate... your probably choked but think of it as the better of the two.. i'm glad you were'nt hurt.. cheers..[addsig]

1065634 if you are jumping any sort of vehicle you want look at what takes the pounding when you land... i would look at a stronger axle set up, hubs, and knuckles... ( horse collar and a helmet might be wise too.. but i'm not your momma)also stronger motor and trany mounts.. you shear those...

1065636 easy... unbolt the fan shroud... unbolt the rad..( it's easier to do on the work bench then in the jeep) line the shroud up with the original holes then move it down an inch.. drill new holes... walla... put every thing back in the jeep and attach the shroud to the new holes... [addsig]

1048529 hey man.. just because we drive jeeps does not mean we cant groove .. it's your ride.. go nuts.. on that note.. go to streetdreams.com find install glossary.. look for the jeep section.. have a look at wrangler 1. has some good ideas on what you can do to your doors, amp rack and...

1048531 no it's not..check out the pin he has on his.. pick one up at a local hardware store.. is good incase you need to use your hilift as a winch..[addsig]

1048536 about a year ago JP magazine did an article on the hummer VS TJ... in the end they said that the tj was by far a superior off road vehicle.. byass? yes... but it had to be said.. any ways, hummer owners from around the us and canada were furious.. writing complaints and threats.. then...

1048549 cool...just wanted to know where's abouts yall from.. thanx..cheers[addsig]

1048565 i saw a suzuki samari with a sticker that said " when i grow up i want to be a jeep" and a jeep that said " when i grow up i want to be a hummer" (i had to give that guy the bird) [addsig]

1048707 check the bulbs... the filiments could be contacting each other making a short circut.. this happened to me.. common because of the vibrations jeeps get from big tires.. and check the switch as well.. [addsig]

1048708 hey.. cool guys.. it just goes to show you gpn is a way of life... i live in Alberta, Canada.. wheel in the foot hills of the rocky mountains and a little in the north.. lots of forests.. cheers...[addsig]

1049319 if you are not going to be doing alot of offroading and it's primaraly a daily driver than you are not too concerned about ground clearence..put a t-case drop in to eliminate any unwanted driveline vibs.. it's not a big deal and is the easiest part of the lift to do.. also do not drive...

1049578 hey... if you need to remove wax on your fender go down to your local body shop supply and pick up a gallon of wax remover... up here thats the only size we can get it in.. follow the directions on the back and, walla, wax less fender.. [addsig]

1049579 LL cool J - back seat of my jeep.. [addsig]