Search results

The front spring retainer is a must for long travel Jeep WJ models. These newly designed retainers will help keep the springs in there place. The new feature includes a 3/8" plate that is drilled and taped 1/2"-20 that gets welded to the upper spring bucket. This design is much stronger than...

I have a few select flex joints up for sale. Made from forged 4130 with a yellow zinc coating. I have 3/4-16 right and left hand thread and 1"-14 right and left hand thread. Uses a 7/16" bolt All are 1.6" in width $45 each Flex Joint 1"-14 Left Hand Thread

These front upper control arms are double adjustable. Right and left hand thread for ease of adjustment. Good for stock length and up to 5" of lift. Includes our in house flex joint. Will fit the following Jeep Models: TJ, XJ, ZJ and WJ Made from 1.5" x .250 wall DOM tubing. Double the...

The WJ front upper spring retainers are on the market now. But with a new design change. A nut will be provided that will be welded to the upper spring can. This will provide more thread and a stronger part. The back side of the retainer will be counter bored for clearance and will also allow...

The wires usually break in the rubber boot between the door and chassis. Also, check all ground wires as well.

We have three new parts coming out on the market for the Jeep Grand Cherokee WJ model. These parts are not on the website yet, but will be soon. We have the front coil spring retainer to help guide the spring to the upper bucket, made from 6061 aluminum, 1" transfer case drop kit and a 1" rear...

Control arms have sold

Control arms have sold..

Listing has been updated with more detail

Listing has been updated

Me to.. I finally have a descent system. Thank you for your help..

Update on the speakers. All wires passed the continuity check. Here are the steps I took to figure this out. 1) Ran jumper wires to one of the front speakers and the speaker was still dead. 2) Performed an ohms test across the poles on all speakers and nothing. 3) Did the 9v battery test on...

Brand new pair of rear upper control arms built for the Jeep TJ model. 2" mounting width Will work from stock to 4" of lift Built by Catoctin Jeep and Off Road Right and left hand thread for easy adjustment while mounted. Both ends use poly bushings that can be replaced. Lifetime warranty on...

For sale is a pair of brand new adjustable lower control arms. Can fit front or rear. Includes our in house flex joint for the adjustment side and fixed at the frame end. Built by Catoctin Jeep and Off Road Lifetime warranty with a one time free poly bushing replacement. Flex end is...

No amp with this setup. As I was checking continuity I did move the wires around at the door, nothing changed.

Hope someone on here can help me out. I have a 2001 Jeep WJ with the none infinity stereo system. The problem is the door speakers. When the Jeep is cold only the dash speakers work, when it sits in the sun for awhile on a warm day then the door speakers kick in. I replaced the head unit...

Replacing front u-joints on the driveshaft

Yes I was on that site and completely understand what is involved, he is very thorough. I was just thinking that if the XJ computer could be used it may simplify the installation. I wasn't sure if the TCU would plug directly to the ECM. If thats not the case then the whole idea my not be worth...

Your probably correct, but it would be something to consider if it would work out. I just looked at the dash of a 2001 XJ and then the dash on my 2001 TJ and both layouts are the same. Looking at the pin outs would seal the deal whether or not it would work.

I know there are a few Jeep TJ owners that have installed the XJ AW-4 auto to replace the 32RH. To take care of the CEL light the ECM is to be replaced from a TJ that had a manual trans in it and then do a pin out with a few wires from the AW-4. My question is, can a ECM from the same year XJ...