Search results

Hi, I'm confused. You say you don't want to spend alot of money, but you're getting a SYE kit and a CV driveshaft??? I still think lengthening the driveshaft (after installing shims) would fix the problem for a reasonable price. The vibrations are likely because you have the slip yoke just...

I'z Jeeplezz Tooz Hi, I don't know much about the Cherokee speed sensors, as my Cherokee is old and has a mechanical cable instead of an electronic sensor for the Speedometer. :mrgreen: However, you should definately get one that has the same type of connection as your old one. Most speed...

Re: RE: Re: This one was done RIGHT! Hi, Check out the EGR system. Make sure the EGR valve isn't stuck open or opening at the incorrect times... if it is it could be the valve itself or the EGR solenoid triggering when it shouldn't be. Another interesting test would be to install a fuel...

Hi, But note that you can certainly create clear photos without Photoshop. :mrgreen: There are many good FREE image editing programs out there. Sure, most don't have all the features of photoshop, but they are still powerful editing programs. Plus they don't cost hundreds of dollars. I like...

Hi, Hmmm, You missed my point. I wasn't trying to compare the reliability of one make vs. another, nor American vs. foreign. Doing so does not provide much useful information, and usually just results in a pissing contest. :wink: Though this discussion is better suited for a new thread...

Hi, You'll probably need more than a "slow" charger. For example, if the welder is pulling 300 amps @ 24 volts, and you are supplying 24 volts by using two 12-volt car batteries in series, you'd likely be draining them fairly quickly. Thus, you'll probably want a charger which can dump a good...

Hi, Yes, the great American car companies that are so corrupted by politics and greed that they have done and continue to do everything they can to suppress certain technologies which would make cars more reliable, last longer, cheaper to operate, inexpensive to maintain, far easier to...

Spark Plug Wire order Hi, I use a Lincoln Pro Mig 175 welder which I bought from Lowe's. They are pretty expensive, but when I bought it Lowe's was running a special on them, so it was cheaper than the current price and came with a cart for the welder. I use the MIG process (Argon/CO2...

Hi, Why don't you just get the driveshaft lengthened??? I got my rear driveshaft lengthened after my EV conversion, as the splined end of the rear driveshaft was not slipping far enough into the transfer case slip yoke, and my U-joint angles were too steep (almost to the point of binding up...

Hi, You can use Automatic Transmission Fluid in most transfer cases. As Beretta said, It is probably worth a shot to fill it up first and see how it does before spending money on a new T-case.... -Nick :!:

RE: I Hi, The product you linked to seems to only be compatible with certain radio head units (and probably OEM ones at that). This means it might not be avaliable for your Jeep and/or costs alot. If you have an aftermarket radio head unit, it may have an auxilary input (like a 1/8" phone...

Hi, When my Cherokee had a starter motor, it was mounted with two standard bolts to the transmission bell housing.... Are you sure they are Torx bolts? -Nick :!:

Hi, Does the rough idle occur based on temperature? driving duration? -Nick :!:

Hi, My Cherokee rear washer doesn't work because the small water hose which runs up the rear wiper arm broke right where it passes through the trunk door to the outside. Perhaps this is your problem as well... -Nick :!:

Re: RE: Jeep vs. Hummer. Hi, 2. Probably not until 1994 or so. Infact, they might not have had a VSS until OBD-II systems were implemented in 1996. 3. I don't know about the 4-cyl or the old V6 engines, but all Cherokees with the fuel injected inline 6 engine have electric fuel pumps. The...

That's Great :lol: :lol: -Nick :!:

Yes, but Centrifugal force doesn't exist. Basically, it is a misnomer used when trying to explain an apparent force acting on an object which is in circular motion, which causes the object to seem to want to fly away (outward) from the center of rotation. Centripetal force, on the other hand...

RE: I got stiffed...(Part Deux) Hi, I don't know, they were talking about "loose" steering. Sounds to me like they have too much power assist? That's why they'd want a larger pulley; to slow the pump down and provide less assist. -Nick :!:

RE: suspension Hi, Should be Centripedal force :P They are not hard to replace, just very time consuming as most cherokees have 3 u-joints on the front driveshaft. You might as well replace them all if you bother to do any. Just be sure you have a vise OR a BFH AND a socket set to use to...

Hi, Try http://www.suspensionconnection.com/ I got shims for $19 from them some time ago... excellent deal -Nick :!: